新闻中心

Company news

Latest news

Contact us

Contact person: Manager Tian

Tel: +86 021-57675460

Mobile phone: +86 15001892679

How to Handle Molding Abnormalities in Rubber Products

Release date:2026-11-09

A great many abnormalities occur during rubber molding — a bit too much flash, one air bubble too many, a chunk scraped off during demolding, and so on. Once accumulated, these abnormalities turn into delivery delays and higher costs. It is therefore critical to establish a standardized, workable mechanism for handling abnormalities. The following explains it from three perspectives.

1 Management Flow for Molding Abnormalities

Molding abnormalities fall into two categories: molding design abnormalities and molding process abnormalities. A molding design abnormality means that a process defined at the development stage fails to meet production requirements in subsequent production, resulting in defective products. A molding process abnormality means that operations in production are not carried out in accordance with work instructions and other requirements, resulting in defective products.

When an abnormality occurs, the first step is to confirm its category, record it in the abnormality log, and issue an abnormality rectification sheet.

图片1.png

The abnormality rectification sheet plays a powerful role in handling abnormalities. It first establishes a rectification team, whose members propose temporary containment measures to prevent the abnormality from worsening and to stop defective products from escaping. It then investigates the occurrence cause and the escape cause, and determines the root cause from the three aspects of adequacy, suitability, and conformity. Next it defines corrective actions (countermeasures): once the occurrence cause is confirmed, targeted solutions and corrective measures are put forward. It then verifies the measures, confirming through improvement verification against the agreed solution that the abnormality will not recur. Finally it standardizes: the verified solution is turned into a standard, and controlled documents are revised or established. It also deploys horizontally, analyzing similar products or items, identifying the same risk points, and standardizing the corrective action in the same way. At the end, the case is confirmed and closed.

图片2.png

2 Improvement of Molding Abnormalities and the Top 30 Molding Defects

All kinds of abnormalities inevitably occur in production, which is why on-line abnormalities deserve close attention. Molding abnormalities are reported by patrol inspectors or production team leaders and are then handled on site by molding process engineers. Any abnormality that cannot be resolved must be escalated promptly — it must never be concealed or left unaddressed — so that there is zero waiting from occurrence to resolution and no defective products are made. Abnormalities that occur each day are analyzed and summarized one by one at the production meeting, where the molding process engineer explains the closure of each product abnormality; abnormalities that cannot yet be closed are analyzed and discussed, and improvement measures are defined — daily abnormalities are cleared daily.

图片3.png

Top 30 molding defects improvement is a rolling management program covering the 30 mass-produced products with the highest defect rates. The molding process engineer compiles categorized statistics on product defects, takes corrective action on the categories with the highest occurrence, investigates the causes, and defines improvement measures.

3 Common Causes of Molding Defects

The table below clearly sets out the common abnormalities, their causes, and the corresponding solutions.

微信图片_4.png

There are no shortcuts in handling molding abnormalities. It requires comprehensive statistics and analysis of the defects of every product, and the use of effective abnormality-handling methods to minimize abnormality problems.

Faced with an endless stream of on-site defects, we do not simply deal with each case as it comes. Instead, we take a systematic approach to pin down the root causes, implement countermeasures, and consolidate standards. With this method we keep resolving every kind of molding abnormality, curb the accumulation of defects at the source, and hold the bottom line on quality, cost, and delivery.


  • Sales Department
  • Contact person: Manager Tian

    Tel: +86 15001892679

    Mailbox: YY301@zhengcun.com.cn

  • Personnel Department
  • Contact person: Ms. Han

    Tel: +86 15001892387

    E-mail: hr@zhengcun.com.cn

         

 Zhengcun Rubber and Plastic Official Wechat

Copyright © Shanghai Zhengcun Rubber and Plastic Industry CO.;    沪ICP备19034625号 Sitemap RSS XML